Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. Maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance
+ 4. Engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and charging system
+ 8. Ignition system
+ 9. Coupling
- 10. Transmissions and power shafts
   - 10.1. Mechanical transmission
      10.1.1. Technical characteristics
      10.1.2. Oil replacement in a transmission
      10.1.3. Removal and installation of the lever of gear shifting
      10.1.4. Removal and installation of a cable of blocking of inclusion of a reverse gear
      10.1.5. Removal, installation and adjustment of draft of gear shifting
      10.1.6. Replacement of sealing rings
      10.1.7. Check, removal and installation of the switch of lamps of a backing
      10.1.8. Removal and installation of a drive of a speedometer
      + 10.1.9. Transmission
   + 10.2. Automatic transmission
   + 10.3. Power shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Electric circuits



10.1.5. Removal, installation and adjustment of draft of gear shifting

Removal

PERFORMANCE ORDER
1. Weaken tightening a bolt on the coupling of draft of gear shifting.
2. Unscrew the screws, drafts of gear shifting fixing a protective tube for the car bottom.
3. Shift back a rubber cover and disconnect the intermediate lever from the basis of the lever of gear shifting.
4. Remove a protective cover from the basis of the lever of gear shifting.
5. Remove draft from the car.
6. Remove a rubber cover from a protective pipe.
7. For dismantling of draft beat out the cylindrical pin, the fixing intermediate lever to a core, then beat out a core from the lever.
8. Take a core from a protective pipe.
9. For removal of the universal hinge сошлифуйте or drill heads of rivets.
10. At installation it is necessary to use special pins and spring brackets which are necessary for getting before removal of rivets.
11. Plugs can be taken from a protective pipe together with a core.

Installation

PERFORMANCE ORDER
1. Fill with silicone greasing of a flute in pipe plugs.
2. A pin new cylindrical fix the intermediate lever to a core, thus their relative positioning should be such, as is shown in drawing.
3. Establish a rubber cover and a casing, thus put on their internal surface silicone greasing. Do not move a protective casing after installation.
4. Establish draft on the car, combining the intermediate lever with the gear shifting lever, and fix screws.
5. Establish a rubber cover about the basis of the lever of gear shifting.
6. Adjust draft.

Adjustment

PERFORMANCE ORDER
1. Remove the central console and establish the gear shifting lever in neutral situation.
2. Working in a motor compartment, a screw-driver remove a stopper from an adjusting opening (it is specified by an arrow) and weaken tightening a bolt (is specified by an arrow) on the coupling of draft of gear shifting.
3. Turn the rod of gear shifting acting from a cover of the mechanism of a choice of transfers counter-clockwise if to look towards a forward part of the car, so, that in the lever of the selector it was possible to insert a drill shaft in diameter of 4,5 mm into adjusting openings and the corresponding openings.
4. Establish draft of gear shifting (with the removed casing).
5. Remove a rubber cover from the basis of the lever of gear shifting and move the lever of transfers in neutral situation to the line of inclusion of the first / second transfer. In this situation adjusting labels (are specified by shooters) on the persistent plug and a casing of the lever of gear shifting should be combined.
6. While the assistant holds the gear shifting lever, in this situation tighten tightening a bolt of the coupling of draft of gear shifting.
7. Take a drill from an adjusting opening.
8. Check that all transfers join well, then establish a new stopper on adjusting openings.
9. Establish a cover of the lever of gear shifting and the central console.