Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. Maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance
+ 4. Engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and charging system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. Suspension bracket and steering
   12.1. Technical characteristics
   + 12.2. Rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. Bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. Nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. Back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a being self-leveled back suspension bracket
   12.15. Removal and installation of a steering wheel
   + 12.16. Steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draft
   + 12.19. Steering transfer
   12.20. Air removal from steering system with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation of a popolnitelny tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. Body
+ 14. Electric circuits



12. Suspension bracket and steering

GENERAL INFORMATION

Details of a forward suspension bracket
1–left rack of a forward suspension bracket,
2–cover,
3–nut of fastening of a rod
shock-absorber,
4–nut of fastening of a rack,
5–top support of a rack,
6–washer,
7–top plate spring,
8–the directing plug,
9–Amortiziruyushchy ring,
10-spring,
11-protective casing,
12-nut,
13-shock-absorber,
14-place of fastening of steering draft,
15-rotary fist,
16-brake board,
17-lock ring,
18-bearing,
19-nave,
20-brake disk,
21-nut of fastening of a power shaft,
22-support,
23-spherical hinge of the bottom lever,
24-nut of fastening of the spherical hinge,
25-clip of the bottom lever,
26-back plug of the bottom lever,
27-bottom lever,
28-arm,
29-plug,
30-sharnirny bolt of the bottom lever,
31-bolt of fastening of the stabilizer of cross-section stability,
32-draft of the stabilizer of cross-section stability,
33-stabilizer of cross-section stability,
34-fastening of the stabilizer of cross-section stability,
35-clip of fastening of the stabilizer of cross-section stability,
36-power shaft

Details of a back suspension bracket
1–shock-absorber,
2–spring,
3–shock-absorber (Hatchback),
4–spring,
5–nut of a nave,
6–persistent ring,
7–external bearing,
8–nave,
9–internal bearing,
10-sealing ring,
11-pin of a nave,
12-longitudinal lever of a back suspension bracket,
13-plug of fastening of a back beam,
14-back stabilizer of cross-section stability,
15-rubber quencher of fluctuations

The independent forward suspension bracket of the Mac-Pherson type includes cylindrical springs and compound telescopic shock-absorbers. Racks of Mac-Pherson fasten to the bottom cross-section levers of a suspension bracket by means of spherical hinges. On rotary fists wheel bearings, brake supports and naves are established. On the majority of models the forward stabilizer of cross-section stability is established

At such design of a forward suspension bracket course stability of the car increases when braking and drift when one party of the car moves on a slippery surface, and another – on a firm covering is excluded.

The back suspension bracket of dependent type consists of a back torsionny beam and longitudinal levers with barrel-like springs and telescopic shock-absorbers. On models of 2,0 l with 16 valves the back stabilizer of cross-section stability is established.

On some models mechanically adjustable being self-leveled back suspension bracket is established.

On cars steering transfer of reechny type is established. For turn of forward wheels steering transfer incorporates to racks of a forward suspension bracket steering drafts.

On some models the amplifier of a steering is established. The drive of the pump of the amplifier of a steering is carried out by a belt from a pulley of a cranked shaft.