Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. Maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance
+ 4. Engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and charging system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. Suspension bracket and steering
   12.1. Technical characteristics
   + 12.2. Rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. Bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. Nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. Back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a being self-leveled back suspension bracket
   12.15. Removal and installation of a steering wheel
   + 12.16. Steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draft
   + 12.19. Steering transfer
   12.20. Air removal from steering system with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation of a popolnitelny tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. Body
+ 14. Electric circuits



12.10. Replacement of back springs

GENERAL INFORMATION

Prevention

Replacements of springs of a back suspension bracket make in pairs.


PERFORMANCE ORDER
1. On cars with a being self-leveled back suspension bracket remove pressure in system.
2. Lift a back part of the car and fix on supports.
Hatchback and Sedan
3. Using the special tool, unload the shock-absorber on the one hand the car for what raise a jack the longitudinal lever (diameter And corresponds to the sizes of a jack).
4. Unscrew bolts of the bottom fastening of the shock-absorber and take the lower part of the shock-absorber from an arm.
5. Lower a jack and remove a spring and rubber bufer. If necessary for extraction of a spring reject the longitudinal lever of a back suspension bracket down.
6. At installation of a new spring it is necessary to establish new rubber bufer.
7. Establish a spring and rubber bufer, then lift the longitudinal lever of a back suspension bracket and fix the lower part of the shock-absorber.
8. At installation of conic springs check correctness of an arrangement (it is specified by shooters) extreme top rounds of a spring in a spring support.
9. Similarly replace a spring from the second party of the car.
10. On models with a being self-leveled back suspension bracket increase pressure in system to 0,8 bar.
Versatile person and Van
11. A jack raise one of longitudinal levers of a back suspension bracket and unscrew a bolt of the bottom fastening of the shock-absorber.
12. Lower a jack and repeat this operation on the other side of the car, leaving a jack on a place.
13. Remove springs, if necessary lowering a jack.
14. At replacement of the top buffers of a spring paste them into place.
15. Establish a spring. At installation of conic springs check correctness of an arrangement (it is specified by shooters) top rounds of a spring.
16. Lift a jack and fix the lower part of the shock-absorber.
17. Rearrange a jack on other party of the car and fix the lower part of the second back shock-absorber.
18. Tighten bolts of the bottom fastening of shock-absorbers the demanded moment.
19. On models with a being self-leveled back suspension bracket increase in system pressure to 0,8 bar.