Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. Maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance
+ 4. Engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and charging system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. Suspension bracket and steering
   12.1. Technical characteristics
   + 12.2. Rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. Bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. Nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. Back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a being self-leveled back suspension bracket
   12.15. Removal and installation of a steering wheel
   + 12.16. Steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draft
   + 12.19. Steering transfer
   12.20. Air removal from steering system with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation of a popolnitelny tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. Body
+ 14. Electric circuits



12.18. Removal and installation of tips of steering draft

GENERAL INFORMATION

Prevention

At removal of a tip of steering draft it is necessary to use a stripper of spherical hinges. At installation it is necessary to use new самоконтрящуюся a nut of fastening of the spherical hinge of a tip of steering draft.


Removal

PERFORMANCE ORDER
1. At existence remove a wheel cap, then weaken bolts of fastening of a forward wheel.
2. Tighten the hand brake, then lift a forward part of the car and fix on supports.
3. Remove the corresponding forward wheel.
4. Weaken a bolt clamping a tip of steering bent for to a carving regulator of steering draft.
5. Unscrew самоконтрящуюся a nut, fixing the spherical hinge of a tip of steering bent for to a rack of a forward suspension bracket.
6. Using a stripper of spherical hinges, take a pin of the spherical hinge of a tip of steering draft from a rack of a forward suspension bracket.
7. Using paint or a sticky tape, note an arrangement of a tip of steering draft on a carving regulator. It is also possible to count number of rounds of a carving on an acting part of a carving regulator.
8. Unscrew a tip from steering draft. The tip right the helmsman of draft is marked by a letter R, and a tip left the helmsman of draft has no marking.

Installation

PERFORMANCE ORDER
1. Screw a tip of steering draft on a carving regulator in the same situation, as before removal.
2. Establish a pin of the spherical hinge of a tip of steering draft on a rack of a forward suspension bracket and fix new самоконтрящейся a nut, having tightened it the demanded moment.
3. Tighten a bolt clamping a tip of steering draft.
4. Establish a wheel and lower the car on the earth.
5. Tighten bolts of fastening of a wheel the demanded moment.
6. Check and, if necessary, adjust corners of installation of forward wheels.