Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. Maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance
+ 4. Engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and charging system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. Suspension bracket and steering
   12.1. Technical characteristics
   + 12.2. Rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. Bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. Nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. Back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a being self-leveled back suspension bracket
   12.15. Removal and installation of a steering wheel
   + 12.16. Steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draft
   + 12.19. Steering transfer
   12.20. Air removal from steering system with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation of a popolnitelny tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. Body
+ 14. Electric circuits



12.6. Adjustment of the bearing of a back wheel

MODELS TILL 1992

PERFORMANCE ORDER

Prevention

For fastening of a nut of a nave it is necessary to use new шплинт.


1. At existence remove a wheel cap, then weaken bolts of fastening of a back wheel.
2. Lift a back part of the car and fix on supports.
3. Remove a back wheel.
4. Using a screw-driver edge, remove a dustproof cap from a nave.
5. Take шплинт, fixing a nave nut from unscrewing, then weaken a nut of fastening of a nave.
6. Tighten a nut of fastening of a nave the moment of 25 Nanometers, thus turn a nave.
7. Weaken a nut of fastening of a nave until while the persistent washer located under a nut, it will be possible to move a screw-driver edge in different directions.
8. Establish new шплинт, fixing a nave nut from unscrewing. Thus, if the opening under шплинт in a pin is not combined with grooves on a nave nut, tighten a nut before combination of an opening with the next groove.
9. Check that the persistent washer can still move. Otherwise weaken a nut before combination of the next groove on a nut with an opening in a nave pin.
10. Establish a wheel and lower the car.
11. Tighten bolts of fastening of a wheel the demanded moment.

MODELS SINCE 1992

Not folding knot of a nave and the bearing of a back wheel on models since 1992

1–nave,

2–fixing element of a nave,

3–bolt,

4–dustproof cap,

5–bearing,

6–sealing ring,

7–ABS sensor

Since 1992 on all models not folding knot of a nave and the bearing of a back wheel is established.

As the knot consisting of a fixing element of a nave, a nave and the nave bearing, is not folding knot, adjustment of the bearing is not required.