Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. Maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance
+ 4. Engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and charging system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
- 13. Body
   13.1. Technical characteristics
   13.2. Care of a body
   13.3. Repair of insignificant damages of a body
   13.4. Repair of strong damages of a body
   + 13.5. Cowl
   13.6. Removal and installation of forward furnish of the car
   13.7. Removal and installation of back furnish of the car
   13.8. Removal and installation of a forward wing
   13.9. Removal and installation of a fairing of a windscreen
   - 13.10. Doors
      13.10.1. Removal and installation of an upholstery of a door
      13.10.2. Removal and door installation
      13.10.3. Removal and installation of the lock of a door
      13.10.4. Removal and installation of the external handle of a door
      13.10.5. Removal and installation of the internal handle of opening of a door
      13.10.6. Removal and installation of the cylinder of the lock of a forward door
      13.10.7. Removal and window regulator installation
      13.10.8. Removal and installation of glass of a door
      13.10.9. Removal and installation of a back door
      13.10.10. Removal and installation of hinges of a back door
      13.10.11. Removal and installation of racks of a back door
      13.10.12. Removal and installation of the lock of a back door
      13.10.13. Removal and installation of the cylinder of the lock of a back door
   13.11. Removal and installation of a trunk lid and торсионов
   13.12. Replacement of components of the lock of a trunk lid
   13.13. Windscreen
   13.14. Removal and installation of back being slightly opened glass
   13.15. Replacement of consolidation of back being slightly opened glass
   13.16. Replacement of an external rear-view mirror
   + 13.17. Seats
   13.18. Removal and installation of head restraints
   13.19. Removal of furnish of a luggage compartment
   13.20. Removal and installation of the central console
   13.21. Removal and installation of a ware box
   13.22. Replacement of seat belts
   13.23. Check and hatch service
   + 13.24. Electric equipment of a body
+ 14. Electric circuits



13.10. Doors

13.10.1. Removal and installation of an upholstery of a door

GENERAL INFORMATION

Operations on removal of an upholstery of a forward door are stated. The upholstery of a back door acts in film similarly, except for noted moments.

PERFORMANCE ORDER
1. On models with a manual window regulator completely close a window and note position of the handle of a window regulator.
2. Release a bracket of fastening and remove the handle.
3. The bracket (it is specified by an arrow) is released if to insert a pure fabric between the handle and an upholstery of a door and, stretching a fabric opposite to the bracket ends, to hook on a bracket and to release it. Thus it is necessary to pull the handle on itself that she after release of a bracket acted in film with шлицов a window regulator.
4. Using a screw-driver edge as the lever, remove decorative furnish of the internal handle of opening of a door.
5. Unscrew the button of blocking of the lock.
6. Using a screw-driver edge as the lever, remove a cap from the screw.
7. Unscrew the screw of fastening of a pocket of a door.
8. Unscrew two screws in the lower part of a pocket and remove a pocket from a door.
9. On back doors remove the ashtray case.
10. Remove a decorative slip from an armrest.
11. Remove an armrest. Fastening of an armrest depends on furnish level, but usually armrests fasten two screws from the forward party. Some armrests also fasten in a back part the ordinary self-cutting screw.
12. On some models the upholstery of a door fastens the self-cutting screws located on perimeter of an upholstery. Using a screw-driver with a wide edge, separate a door upholstery from a door.
13. If necessary remove a protective film from a door.
14. Installation is made in sequence, return to removal.