Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. Maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance
+ 4. Engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburetor
      6.1.1. Technical characteristics
      6.1.2. Use of unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and fuel level sensor installation
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management by an air zaslonka
      + 6.1.11. Carburetors
      6.1.12. Check of the electromagnetic valve of interruption of supply of fuel
      6.1.13. Removal and carburetor installation
      - 6.1.14. Carburetor repair
         6.1.14.1. TL carburetor 32
         6.1.14.2. Carburetor of 35 PDSI
         6.1.14.3. Carburetor 1В1
         6.1.14.4. Carburetor 2Е3
         + 6.1.14.5. Varajet II carburetor
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and installation of an exhaust system
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and charging system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Electric circuits



6.1.14. Carburetor repair

6.1.14.1. TL carburetor 32

GENERAL INFORMATION

Arrangement of the screw of fastening of an arm of support of a cable of management of an air zaslonka, caps, screw of adjustment of quality of a mix and idling turns

And – the screw of fastening of an arm of support of a cable of management of an air zaslonka,

In – a cap,

With – the screw of adjustment of quality of a mix,

D–screw of adjustment and idling turns

Arrangement in a cover of the carburetor of caps, a jet of idling, an additional air jet and a jet of a fuel mix

And, In – caps,

With – a jet of idling,

D–additional air jet,

Е–jet of a fuel mix

Prevention

If the carburetor demands major maintenance, it is economically more favorable to replace the carburetor. It is usually necessary to assort the carburetor for cleaning of jets and carburetor channels.


PERFORMANCE ORDER
1. Remove the carburetor from the engine.
2. Using suitable solvent or gasoline, clear an external surface of the carburetor and dry up it. Prepare a pure workplace.
3. Remove a returnable spring of a butterfly valve from draft and an arm sideways the carburetor.
4. Disconnect a vacuum hose from a branch pipe of the vacuum chamber located on the case of butterfly valves.
5. Unscrew 4 screws (are specified by shooters) fastenings of a cover of the carburetor.
6. Uncover the carburetor the carburetor.
7. In the basis of the carburetor unscrew the screw (the fixing case of an air zaslonka to the case of the poplavkovy chamber is specified by an arrow), and divide cases.
8. Unscrew the screw, a fixing arm of support of a cable of management of an air zaslonka to the case of an air zaslonka and remove it (see fig. Arrangement of the screw of fastening of an arm of support of a cable of management of an air zaslonka, caps, screw of adjustment of quality of a mix and idling turns). Release a clamp and take from a casing a sealing ring.
9. Screw in against the stop screws of adjustment of quality of a fuel mix and idling turns, but thus count quantity of turns of screws, then unscrew screws completely.
10. Unscrew four screws and uncover diaphragms of the accelerating pump and a spring the case of the poplavkovy chamber.
11. On the other side of the case of the poplavkovy chamber unscrew three screws and uncover diaphragms of the mechanism of enrichment and a spring.
12. Take a spray from a casing.
13. Using a drift, beat out a rotary axis of floats (it is specified by shooters) and, using flat-nose pliers, take it from a nest.
14. Remove floats and laying of a cover of the carburetor.
15. Remove the needle valve of the carburetor, then unscrew the main jet (it is specified by an arrow).
16. Note an arrangement and unscrew all jets and caps from a carburetor cover (see fig. An arrangement in a cover of the carburetor of caps, a jet of idling, an additional air jet and a jet of a fuel mix). Unscrew an emulsion tube from an opening of an additional air jet.
17. Take from a diffuzor the main spray.
18. Unscrew a stopper and take the fuel filter located adjacently with a branch pipe of supply of fuel.
19. If necessary remove from the top cover of the carburetor the vacuum chamber together with the draft operating an air zaslonka.
20. Remove a cam and a spring, disconnect draft from a cam and the lever of a drive of an air zaslonka and remove knot in collecting (And – screws of draft of a zaslonka, In – spring brackets).
21. Clear carburetor details in gasoline and blow them the compressed air.
22. Blow the compressed air all jets and channels in the carburetor, but thus do not use a wire.
23. Check a condition of all axes and drafts on existence of wear and the increased gap. In the presence of defects replace worn-out details.
24. Check a condition of diaphragms and replace them in the presence of punctures and pollution.
25. Check a condition and tightness of a float. If in a float there is a fuel, replace it.
26. Blowing the needle valve, check its tightness in a closed position. In the absence of tightness replace the needle valve.
27. Collect the carburetor in sequence, return dismantling, and make the main adjustments of the carburetor.
28. Check height of installation of a float and, if necessary, turning in the lever, establish the demanded height (And – a place of measurement of height of installation of a float, In – a place for adjustment of height of installation of a float).
29. Establish the carburetor on the car and adjust turns of idling and quality of a fuel mix.