Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. Maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance
+ 4. Engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and charging system
- 8. Ignition system
   - 8.1. Ignition system with the breaker
      8.1.1. Technical characteristics
      8.1.2. Check of system of ignition
      8.1.3. Adjustment of a gap and the closed condition of contacts of the breaker
      8.1.4. Removal and installation of contacts of the breaker
      8.1.5. Check, removal and condenser installation
      - 8.1.6. Ignition distributor
         8.1.6.1. Removal and installation of the distributor of ignition
         8.1.6.2. Repair of the distributor of ignition
      + 8.1.7. Adjustment of a corner of an advancing of ignition
      8.1.8. Removal, check and installation of the coil of ignition
   + 8.2. Electronic contactless system of ignition
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Electric circuits



8.1.6. Ignition distributor

8.1.6.1. Removal and installation of the distributor of ignition

Removal

PERFORMANCE ORDER
1. Mark and disconnect high-voltage wires from spark plugs.
2. Unscrew spark plugs.
3. Unscrew the screws, fixing a cover of the distributor of ignition, uncover and move it aside.
4. With the released hand brake and the included transfer close an opening for a candle of the first cylinder a finger and move the car forward to those, yet will not feel compression in the first cylinder.
5. Move the car further before label combination (it is specified by an arrow) on a pulley of a cranked shaft with the index on a cover.
6. Thus the rotor of the distributor should be combined with a label on the case of the distributor of ignition.
7. Disconnect from the ignition distributor the electric socket and a vacuum tube from a vacuum regulator of an advancing of ignition.
8. Unscrew a bolt, fixing a tightening level of the distributor of ignition, remove a bolt, a tightening level and the ignition distributor.

Installation

PERFORMANCE ORDER
1. Check that the adjusting label on a pulley of a cranked shaft is combined with the index.
2. At installation of the distributor of ignition, the shaft of the distributor will slightly turn counter-clockwise at connection of gear wheels.
3. After installation check correctness of position of the distributor of ignition, thus a rotor of the distributor it should be combined with a label on the case of the distributor of ignition.
4. Before installation turn a shaft of the distributor of ignition so that the rotor of the distributor was directed to a sealing ring of wires of the distributor of ignition (And – a sealing ring of wires, In – a label of combination of N1). At installation of the distributor of ignition the rotor will be established in the correct situation.
5. It is also necessary to turn a power shaft of the oil pump in such situation that ledges of a shaft were combined with a groove in a shaft of the distributor of ignition. Turn a shaft so that ledges settled down at an angle 90 ° to an axis of a cranked shaft.
6. Check correctness of an arrangement of a sealing ring of round section in the basis of the distributor of ignition and establish the ignition distributor into place.
7. For the correct installation of the distributor of ignition, probably, it is required to make this operation several times.
8. After installation of the distributor of ignition into place turn the case of the distributor of ignition clockwise on some degrees so that contacts of the breaker became isolated, then slowly turn it counter-clockwise till the beginning of disconnection of contacts.
9. In this position of the distributor of ignition establish a tightening level and fix it a bolt.
10. Connect to the ignition distributor the electric socket and a tube of vacuum correction.
11. Screw in spark plugs, establish a cover of the distributor of ignition and high-voltage wires.
12. Adjust a corner of an advancing of ignition.